Search found 19 matches

by black1q
Thu Sep 20, 2012 1:08 pm
Forum: Tips and Tricks
Topic: Printing with ABS
Replies: 22
Views: 8324

Re: Printing with ABS

Ops I forget to say, if you want the print structur at the first layer instead of the solution you only need to print with raft and remove the raft later on.
by black1q
Thu Sep 20, 2012 1:05 pm
Forum: Tips and Tricks
Topic: Printing with ABS
Replies: 22
Views: 8324

Re: Printing with ABS

@ HLA No I have no issues, its like printing with PLA except that a layer of the solution will still stick on the bottom of the object, but this layer is as even as the printbed. I will make some pictures the next days, meanwhile you can take a look at the high quality section. My blue owl was print...
by black1q
Tue Sep 18, 2012 2:33 am
Forum: Tips and Tricks
Topic: Printing with ABS
Replies: 22
Views: 8324

Re: Printing with ABS

SUCCESS !!! :D Meanwhile I made a few prints with ABS. I made the ABS solution like described before (some ABS filament in a few drops of Acetone) take an old brush and spread it thin on my Kapton covered printbed. I get the best results with the heated bed and raft, without raft it is very very ve...
by black1q
Mon Sep 17, 2012 9:50 am
Forum: General
Topic: High quality prints
Replies: 103
Views: 18191

Re: High quality prints

@Kjetilei I dont know if this helps, but I once my filament gets stuck, and I take a 0,30 mm drill in my hand to reopen my nozle from the oposite site, I also heated it up a little more and I cleaned the brass wheel with a needle and then it worked again. @Guilliaume Maybe you should print the criti...
by black1q
Fri Sep 14, 2012 4:08 am
Forum: General
Topic: High quality prints
Replies: 103
Views: 18191

Re: High quality prints

Heeeeelp ????!!!???!!!! Of cause I saved the settings, else it would not calculate 750 layers for the owl, but I found out that pronterface at the end always calculate with 0.25 between the layers. Thats pretty strange because on the same computer with the same settings I could print my own objects ...
by black1q
Thu Sep 13, 2012 1:04 pm
Forum: General
Topic: High quality prints
Replies: 103
Views: 18191

Re: High quality prints

Hi Guillaume, I have to agree that Kjetilei is right with his opinion about the quality and the sending the objects. I tired to print the octopus and the torture object but both only result in an error, maybe my download was damaged because I never had a problem with any other objects. The quality o...
by black1q
Wed Sep 12, 2012 12:31 pm
Forum: General
Topic: High quality prints
Replies: 103
Views: 18191

Re: High quality prints

Sadly I did not write down the error and I dont find any version information in Pronterface. I now print the owl again with Oozebane activated and in 0.1 resolution ind ABS plastic, until now it looks perfect. I also reduced the temperature to 228° and raised the speed to 3250. I will send the objec...
by black1q
Wed Sep 12, 2012 11:29 am
Forum: General
Topic: High quality prints
Replies: 103
Views: 18191

Re: High quality prints

I dont understand whats going on, but the torture object also dont work.
I now try again the owl in high resulution to see if this is a problem with my computer.
by black1q
Wed Sep 12, 2012 10:22 am
Forum: General
Topic: High quality prints
Replies: 103
Views: 18191

Re: High quality prints

I wanted to print the octopus, but the model dont work! I tried it several times with different settings but Skeinforge always produce an error. Has anyone else printed the Octopus?
by black1q
Wed Sep 12, 2012 5:41 am
Forum: General
Topic: High quality prints
Replies: 103
Views: 18191

Re: High quality prints

Hi Kjetilei, sorry I forget to answer your question.
I printed in the standard speed, I did not change anything.

Go to advanced search