Search found 8 matches

by weigu
Tue Sep 22, 2020 10:18 am
Forum: Electronics
Topic: Duet control board
Replies: 2
Views: 1509

Re: Duet control board

Hi,

I pimped my Felix with a duet 3 6HC mainboard. More infos on:

file:///savit/www.weigu/other_projects/3d_printing/fe ... index.html
by weigu
Sat Nov 30, 2019 4:48 pm
Forum: General
Topic: TEC4 Resume print without homing
Replies: 2
Views: 1667

Re: TEC4 Resume print without homing

Hi Guillaume, To print the first colour to a defined height I used your last Simplify FFF file, deleted the Ending Script and replaced it only with: G91 G1 Z20 F5000 G90. So there is no M84 or similar. Does perhaps the firmware itself stops the motors after some minutes of inactivity? With which com...
by weigu
Tue Nov 26, 2019 4:06 pm
Forum: General
Topic: TEC4 Resume print without homing
Replies: 2
Views: 1667

TEC4 Resume print without homing

Hi, I'm using a Felic TEC4 dual with Simplify3D or octoprint. When printing with one extruder and more colours (changing at different heights) like described here: http://weigu.lu/other_projects/3d_printing/index.html , I have some times the problem, that when I send the second g-code file (beginnin...
by weigu
Wed Nov 01, 2017 9:04 am
Forum: General
Topic: Felix Tec 4 Upgrade: Installed
Replies: 19
Views: 3468

Re: Felix Tec 4 Upgrade: Installed

Thanks Guillaume,
This worked. Greetings Guy
by weigu
Tue Oct 31, 2017 11:59 am
Forum: General
Topic: Felix Tec 4 Upgrade: Installed
Replies: 19
Views: 3468

Re: Felix Tec 4 Upgrade: Installed

Hi again,
The sensor is working at 12V! Can I use the 12 V from the power supply directly (whats about the resistor and the diode)?
by weigu
Tue Oct 31, 2017 10:58 am
Forum: General
Topic: Felix Tec 4 Upgrade: Installed
Replies: 19
Views: 3468

Re: Felix Tec 4 Upgrade: Installed

Hello gfeliksdal,

The board is an V2.1. No the LED is always out, I get no reaction with metal.
I measure 5,4V between GND and VCC and 4,77V between GND and Signal.
The data sheet says 10-30 V for power supply?

Thanks
Guy
by weigu
Mon Oct 30, 2017 6:32 pm
Forum: General
Topic: Felix Tec 4 Upgrade: Installed
Replies: 19
Views: 3468

Re: Felix Tec 4 Upgrade: Installed

Hi again,
My sensor is an E2BM12KS04 WP C2.
@Kerog; what type did you get?
by weigu
Mon Oct 30, 2017 5:43 pm
Forum: General
Topic: Felix Tec 4 Upgrade: Installed
Replies: 19
Views: 3468

Felix Tec 4 Upgrade: Installed. Problem with Z axes

Hi, Like kerog, I upgraded from 3 to 3.1 and now to Tec4 (dual). I have a problem with the Z-probe. When I do a Z-calibration (over display) it stops at 4 cm and I have to scroll a very long way down. The bed leveling takes part at approx. 2 cm from the bed (is this normal?) and says the bed is leve...

Go to advanced search