Search found 22 matches

by fanass
Thu Mar 31, 2016 9:25 am
Forum: Hacks and printer upgrades
Topic: Looking for OPT1/OPT2 documentation and free Pins
Replies: 29
Views: 7887

Re: Looking for OPT1/OPT2 documentation and free Pins

I use a capacitive sensor instead. They can be attached and used in a similar way and recognize glass plates and other material.
by fanass
Mon Feb 15, 2016 11:30 am
Forum: Troubleshooting
Topic: felix Pro 1 Huge shifting during printing
Replies: 5
Views: 1994

Re: felix Pro 1 Huge shifting during printing

I had this effect a few months ago.
Tightening the screw of a pulley fixed my problem.
Check that the screws are tightend and attaching
the flattend part of the stepper-axis.
by fanass
Mon Sep 28, 2015 1:10 pm
Forum: Electronics
Topic: ControlBoard OPT1 & OPT2 Pinout
Replies: 2
Views: 3601

Re: ControlBoard OPT1 & OPT 2 Pinout

Thanks a lot, Bill
by fanass
Tue Sep 15, 2015 6:50 am
Forum: Hacks and printer upgrades
Topic: Looking for OPT1/OPT2 documentation and free Pins
Replies: 29
Views: 7887

Re: Looking for OPT1/OPT2 documentation and free Pins

@seaton, i verified successfully pin 41 with a multimeter. Other Pins were more difficult, because of the small smd-technology (and my nervous fingers ;) ). I could'nt identify them exactly. @wilco02 tnx fr info. I found the display layout in the firmware. I do not found any free ports and the layou...
by fanass
Fri Sep 11, 2015 6:53 am
Forum: Hacks and printer upgrades
Topic: Looking for OPT1/OPT2 documentation and free Pins
Replies: 29
Views: 7887

Re: Looking for OPT1/OPT2 documentation and free Pins

Wilco02, i'm looking for the pin layout too. I got no answer
from felixprinters. I identified only one pin (Digitil Pin 41 on Opt1). Sry.
by fanass
Mon Sep 07, 2015 9:12 am
Forum: Hacks and printer upgrades
Topic: Looking for OPT1/OPT2 documentation and free Pins
Replies: 29
Views: 7887

Re: Looking for OPT1/OPT2 documentation and free Pins

Thanks a lot for information sator! As you can see here: http://www.felixprinters.com/media/catalog/product/cache/1/image/1200x/0f0abe33d279b40e6cecf91ca8f04913/_/m/_mg_0435-15-14.jpg the felixboard has two 6-pin connectors. Looking at that image, OPT1 seems to have a circuit wire to Digital Pin 41 ...
by fanass
Fri Sep 04, 2015 12:27 pm
Forum: Hacks and printer upgrades
Topic: Looking for OPT1/OPT2 documentation and free Pins
Replies: 29
Views: 7887

Looking for OPT1/OPT2 documentation and free Pins

i would like to add an Z_MAX_ENDSTOP Sensor to my felix3.0 to improve Z-Probe and autobed levelling.
How can i connect the Opto-Sensor to the board (Guillaume?).
tia
by fanass
Fri Sep 04, 2015 12:21 pm
Forum: Hacks and printer upgrades
Topic: Inductance Auto Leveller
Replies: 3
Views: 1196

Re: Inductance Auto Leveller

Seaton, i've tried an (capacitive) Sensor for autobed levelling and got frustrated. I mounted the sensor near to the hotends, removed the z-sensor wires and connected the capacitive-sensor to the z-sensor connector (via optocopler). The sensor itself works like a charm. The firmware detects, when th...
by fanass
Fri May 22, 2015 7:17 am
Forum: Mechanics
Topic: Bed is not flat anymore ;(
Replies: 9
Views: 9258

Re: Bed is not flat anymore ;(

I have no answers to your questions, im am interested in the answers too. I recognized distortion of the bed too. But the other way round. The hotend touches in the corners and is about 1mm above the bed in the center. Half a year of printing too. It's anoying, because i adjusted the distance to the...
by fanass
Fri Apr 03, 2015 9:57 am
Forum: Tips and Tricks
Topic: Printinz Printer Plate first impressions
Replies: 17
Views: 3584

Re: Printinz Printer Plate first impressions

Thanks a lot Stephen, finally i got nearly perfect results with ABS. I adjusted the z-axis distance very precicly and i switched from kisslicer to Simpify3D, which prints with much more speed per default than my kisslicer-setup before. Additionaly i reduced the temperature again. It was a tricky pro...

Go to advanced search