Search found 12 matches

by toonlumberjack
Mon Dec 11, 2017 9:56 am
Forum: Troubleshooting
Topic: First Layer with 0.1mm - still struggling
Replies: 1
Views: 874

First Layer with 0.1mm - still struggling

Basically it's a trouble shooting thread, but to get an overall-impression I would totally appreciate, if at least a few members can share their point of view on the topic. Probably we all can get something good out of this :) I'm owning a Felix Printer 3.1. the left front corner (max_x,max_y) of th...
by toonlumberjack
Mon Dec 11, 2017 9:28 am
Forum: Troubleshooting
Topic: Display problem
Replies: 2
Views: 1055

Re: Display problem

I thought that i did reply.

Anyway. Yes i FORGOT that the display is initialized at the start.

So thank you very much for the reminder
by toonlumberjack
Tue Feb 14, 2017 9:28 am
Forum: Troubleshooting
Topic: Filament Transport doesn't work
Replies: 2
Views: 441

Re: Filament Transport doesn't work

Oh my god ...Yes you are right. Found the the part with it

#define EXT0_WAIT_RETRACT_TEMP 150

Due to teardown i havent connected the extruders hotends. Will check this.

Will report about the test

thank you very much for now.
by toonlumberjack
Fri Feb 10, 2017 7:49 pm
Forum: Troubleshooting
Topic: Filament Transport doesn't work
Replies: 2
Views: 441

Filament Transport doesn't work

With Felix Dual 3.1 Both filament transports don't work. 1) Checking if Motostepers are defect Plugged the motor steppers to the functional x/y/Z stepper connection -> They are working 2) Checkec cablebreak Multimeter did *piep on every wire of the 4. For both of extruder motors 3) Checkec Board Pin...
by toonlumberjack
Fri Feb 10, 2017 7:35 pm
Forum: Electronics
Topic: Working F 3.1 , but Display doesn't
Replies: 7
Views: 1391

Re: Working F 3.1 , but Display doesn't

Sorry to response and close this topic

SOLVED.... The flatcable orientation was on a few set of displays on the wrong side and additionally i plugged the display in AFTER starting the board
by toonlumberjack
Fri Feb 10, 2017 7:32 pm
Forum: Troubleshooting
Topic: Display problem
Replies: 2
Views: 1055

Re: Display problem

Have you plugged the display in BEFORE you started the mainboard?
by toonlumberjack
Wed Aug 17, 2016 8:39 am
Forum: Electronics
Topic: Shifting and hot electronics
Replies: 7
Views: 1679

Re: Shifting and hot electronics

matthijs wrote:Hi,

Check the assembly manual, page 29 (step 89).
It shows a picture of trim potmeter settings that usually work.
You can download the manual here: http://www.felixprinters.com/downloads/ ... IX_3.1.pdf.

I am aware of the settings and double checked them.
by toonlumberjack
Wed Aug 17, 2016 8:35 am
Forum: Electronics
Topic: Working F 3.1 , but Display doesn't
Replies: 7
Views: 1391

Re: Working F 3.1 , but Display doesn't

matthijs wrote:You also see this pattern on the display when the flat cable is inserted the wrong way around.
Really? the red cable normally indicates pin 1 in electronics and was on the right side according to the assembly guide.

Switching it the display went black.
by toonlumberjack
Tue Aug 16, 2016 7:48 am
Forum: Electronics
Topic: Shifting and hot electronics
Replies: 7
Views: 1679

Re: Shifting and hot electronics

There is documentation in the manual /assembly instructions. 1. Turn the screw fully counter-clockwise. 2. Turn it clockwise a quarter turn. This will give a good starting point for finetuning later. from Instruction_Manual_of_Felix_1_5b_v2.pdf I am not sure about that. The part was printed correct...
by toonlumberjack
Tue Aug 16, 2016 7:43 am
Forum: Electronics
Topic: Working F 3.1 , but Display doesn't
Replies: 7
Views: 1391

Re: Working F 3.1 , but Display doesn't

Thank you very much for this advice. Will try it this evening and give a short report.

I'm curious if this is the problem. I double checked the potentiometers settings during the assembly.

Go to advanced search