Search found 19 matches

by Danny-Lelystad
Fri Oct 04, 2013 1:27 pm
Forum: Hacks and printer upgrades
Topic: New extruder carriage design for E3D Bowden Hot end V5
Replies: 121
Views: 20503

Re: New extruder carriage design for E3D Bowden Hot end

Looks great Satoer, i will try the bowden feeder in my Felix 2.0 with 'original' Felix hotend somewhere in the next couple of weeks. I already use a bowden cable to guide filament, its a pneumatic tube with inner diameter 2.0 mm
by Danny-Lelystad
Fri Oct 04, 2013 12:23 pm
Forum: Assembly
Topic: Opto sensor issue??
Replies: 6
Views: 1922

Re: Opto sensor issue??

If this is the wiring order u used and u did use the same on the Felix pcb itself, then there is an error in ure wiring :( U should switch the black and yellow at the optosensors. At the optosensor u use this order (Look at the optosensor pcb, the small letters next to the screwterminal): Yellow is ...
by Danny-Lelystad
Sat Aug 31, 2013 9:35 pm
Forum: Electronics
Topic: Felix 2.0 opto sensors in kit not working
Replies: 5
Views: 1317

Re: Felix 2.0 opto sensors in kit not working

Hi, please look very good at the optosensors. There are different types deliverd. According the manual you should connect the wires in order: Red, Black, Yellow. But i know there are sensors where the signal is in the middle. See attatched picture, thats the one from the manual. I don't have picture...
by Danny-Lelystad
Sat Aug 17, 2013 8:15 am
Forum: General
Topic: Felix copycat from China
Replies: 11
Views: 2002

Re: Felix copycat from China

Here is the same China product for a better price:
http://www.aliexpress.com/item/3D-print ... 34066.html
by Danny-Lelystad
Thu Aug 01, 2013 7:34 pm
Forum: Electronics
Topic: Felix 2 LCD Backlight?
Replies: 31
Views: 5836

Re: Felix 2 LCD Backlight?

Kentxu wrote:Thanks Seaton and Danny for the suggestions.
It's been a long slog, but I'm finally there! Working Display :mrgreen:

Happy Printing! Ken
Good to see u found the problem Ken. And you are right about quality control, this display should never be sent to u.
by Danny-Lelystad
Thu Aug 01, 2013 7:29 pm
Forum: Electronics
Topic: Felix 2 LCD Backlight?
Replies: 31
Views: 5836

Re: Felix 2 LCD Backlight?

If i check the display connector on the Felix 2.0 pcb i get on all datalines (D0-D7) signals, see below:
8-channel logic analyzer on D0-D7 from the displayport at a Felix 2.0 pcb
8-channel logic analyzer on D0-D7 from the displayport at a Felix 2.0 pcb
by Danny-Lelystad
Sun Jul 28, 2013 9:29 pm
Forum: General
Topic: Next version wannahaves
Replies: 100
Views: 83198

Re: Next version wannahaves

Oh, and there's one more thing: All the 3 plastic parts that trigger the optosensors should be delivered printed with black plastic,...... I replaced the tapes with kapton tape coloured black with permanent ink, and that has worked so far, but the whole thing is a sort of a hack, and it would be mu...
by Danny-Lelystad
Sun Jun 23, 2013 3:57 pm
Forum: Electronics
Topic: Felix 2 LCD Backlight?
Replies: 31
Views: 5836

Re: Felix 2 LCD Backlight?

Try to adjust the contrast with the little blue poti next to displayconnector, turn to the right slowly until u see the text. See pictures on this forum: http://fablabdronten.freeforums.org/felix-3d-printer-2-0-lcd-scherm-aansluiten-t3.html (its in dutch, but picture is enough to see which connector...
by Danny-Lelystad
Thu Jun 20, 2013 10:55 pm
Forum: Software/Firmware
Topic: Felix 2.0 LCD Menu structure
Replies: 1
Views: 696

Felix 2.0 LCD Menu structure

Today my LCD panel from felixprinters starts working with some help from Guillaume. In case you have problems with the lcd panel (shows only 2 rows of text) you should update the firmware from your Felix2.0 printer (get it from the download section). The right boardsetting for the Arduino software (...
by Danny-Lelystad
Thu Jun 20, 2013 7:59 pm
Forum: Electronics
Topic: Power up felix 2.0 witout repetier host
Replies: 4
Views: 2490

Re: Power up felix 2.0 witout repetier host

Well ure very right about the 'cooldown' menu option. Hotend is turned off, but the bed isn't. That must be an mistake in the firmware. I will try to find a way to fix this one. About the manual, ure right, there are a few mistakes. The menu structure from the pdf in the firmware is also an old one....

Go to advanced search