Search found 270 matches

by Hugues
Wed Mar 15, 2017 12:54 pm
Forum: Troubleshooting
Topic: 3D printing is a Fire Hazard!
Replies: 5
Views: 29027

Re: 3D printing is a Fire Hazard!

That sounds like something that should be added to our printer,

would like to hear from Felix about this !
by Hugues
Sat Jan 14, 2017 12:05 pm
Forum: Repetier-Host
Topic: can't switch on extruder from user interface
Replies: 4
Views: 1314

Re: can't switch on extruder from user interface

problem solved,
****
In Printer-Settings->Extruder you define max. temperature for host. Sliders will adjust to that range so if that is 0 you can not go higher there but can still send the gcode to do otherwise.
*****
by Hugues
Tue Jan 10, 2017 1:08 pm
Forum: Repetier-Host
Topic: can't switch on extruder from user interface
Replies: 4
Views: 1314

Re: can't switch on extruder from user interface

Hi Feliks, the thermistors are ok, because when i send the GCODE command manually to set the temperature at 210C, the temperature goes up and then stabilizes around 210C. I never tried to print from a SD card. I don't have the display unit. I will check for the Repetier version number when i get bac...
by Hugues
Sat Jan 07, 2017 3:48 pm
Forum: Repetier-Host
Topic: can't switch on extruder from user interface
Replies: 4
Views: 1314

can't switch on extruder from user interface

Hi guys, weird problem happening out of nowhere today: in Repetier, i cannot switch on my extruder anymore to heat up. I click on the little icon with the red slash, but it stays off. I cannot set the temperature, i enter 210 and press enter, it comes back to zero. Never had this before. Bed works f...
by Hugues
Sat Dec 03, 2016 7:53 pm
Forum: Repetier-Host
Topic: How to remove printer inactivity timeout
Replies: 3
Views: 1336

Re: How to remove printer inactivity timeout

ok, found the parameter, seems to be working indeed
thanks
by Hugues
Sat Dec 03, 2016 7:45 pm
Forum: Repetier-Host
Topic: can't connect to printer from serial port
Replies: 1
Views: 1219

Re: can't connect to printer from serial port

found it,
googled the error message
i increased the baud rate from 115 200 to 250 000 and it worked
strange as i tried that earlier and i got message that ma was 115 200
by Hugues
Sat Dec 03, 2016 2:10 pm
Forum: Repetier-Host
Topic: can't connect to printer from serial port
Replies: 1
Views: 1219

can't connect to printer from serial port

I cannot connect to my Felix 3.0 anymore from a laptop thatused to work, printer works fine from another laptop, so not sure what is the problem i have updated repetier software with latest version, you can see my printer settings below and the messages i get in the log when trying to connect, pictu...
by Hugues
Sat Dec 03, 2016 2:07 pm
Forum: Repetier-Host
Topic: How to remove printer inactivity timeout
Replies: 3
Views: 1336

Re: How to remove printer inactivity timeout

good idea,i'm going to check this

although i cannot connect to myprinter currently,i'll start another post on this

thanks
by Hugues
Fri Dec 02, 2016 9:10 pm
Forum: Repetier-Host
Topic: How to remove printer inactivity timeout
Replies: 3
Views: 1336

How to remove printer inactivity timeout

Hi guys, i would like to use my print bed as a heating plate, i need to keep it at 37 C all night, But if i leave the printer connected to my PC with the bed heater on, after a certain time, the heater stops working, looks like there is a inactivity timeout somewhere. I check the various configurati...
by Hugues
Thu Feb 25, 2016 9:05 pm
Forum: General
Topic: Hotbed warped
Replies: 3
Views: 3906

Re: Hotbed warped

could a "thick enough" glass sheet help correct the issue a bit ?

I do have a glass sheet on mine, 2-3 mm thick i would say.

If the alu sheet bends more than the glass sheet, it would then help.

Worth a try, glass is cheap.

Go to advanced search