Thx for sharingviina wrote:Hi!
Jann from Simplify3D sent me Felix 3.0 PLA profile.
Thanks!!
Search found 132 matches
- Thu Apr 03, 2014 6:30 am
- Forum: Software/Firmware
- Topic: Simplify3D Software
- Replies: 74
- Views: 17741
Re: Simplify3D Software
- Fri Mar 07, 2014 8:22 am
- Forum: Mechanics
- Topic: When Should the 2 Small Vertical Fans go?
- Replies: 5
- Views: 1365
Re: When Should the 2 Small Vertical Fans go?
The fans cooling the cold end?
They should run all the time!
They should run all the time!
- Fri Mar 07, 2014 8:21 am
- Forum: Assembly
- Topic: Felix 3.0 kit - Kapton tape replaced with Kapton sheet?
- Replies: 7
- Views: 1734
Re: Felix 3.0 kit - Kapton tape replaced with Kapton sheet?
Take a picture and upload here.
Really want to see what you are talking about
Really want to see what you are talking about
- Wed Mar 05, 2014 7:21 pm
- Forum: Software/Firmware
- Topic: Hot end temperature
- Replies: 4
- Views: 1053
Re: Hot end temperature
P is the proportional value of the controller
I the integral and
D the differential
I would only tweak the I value and if you do overshoot too much change the D value
I the integral and
D the differential
I would only tweak the I value and if you do overshoot too much change the D value
- Wed Feb 26, 2014 3:55 pm
- Forum: Software/Firmware
- Topic: Simplify3D Software
- Replies: 74
- Views: 17741
Re: Simplify3D Software
@Saamec
Sure
But using E3D Bowden extruder (now Kraken) with retraction of 5mm
Sure
But using E3D Bowden extruder (now Kraken) with retraction of 5mm
- Tue Feb 25, 2014 12:03 pm
- Forum: Software/Firmware
- Topic: Simplify3D Software
- Replies: 74
- Views: 17741
Re: Simplify3D Software
Did make a failure with Kisslicer and printed 50'% filledchrisblanchard wrote:Bachgassenbande,
What is the print time difference on those two?
Repetier told me it would take 10h but did take 16h
Simplify3D did take 5h30min as calculated from the software to print with 35% infill
- Sun Feb 23, 2014 11:13 am
- Forum: Software/Firmware
- Topic: Simplify3D Software
- Replies: 74
- Views: 17741
Re: Simplify3D Software
Did a comparison print with my Kraken setup.
Right side Kisslicer left side Simplify3d
Maybe you can't see it that good on the picture but Simplify3d result is much better according details.
Especially the "greeting" tentakle has much better details than the one from Kisslicer
Right side Kisslicer left side Simplify3d
Maybe you can't see it that good on the picture but Simplify3d result is much better according details.
Especially the "greeting" tentakle has much better details than the one from Kisslicer
- Sat Feb 22, 2014 9:16 pm
- Forum: Software/Firmware
- Topic: Simplify3D Software
- Replies: 74
- Views: 17741
Re: Simplify3D Software
Update 23rd of Feb - Issue solved needed to set the center for the machine for x and y to zero. Offset is than also not needed anymore What settings do you use Seaton? What profile? Replicator 2 as default and than use the Felix dimensions and steps? I just made my own profile and saved it, now show...
- Fri Feb 21, 2014 11:04 am
- Forum: Software/Firmware
- Topic: Simplify3D Software
- Replies: 74
- Views: 17741
Re: Simplify3D Software
No haven't seen it till now
Just playing a little
Just playing a little
- Fri Feb 21, 2014 10:21 am
- Forum: Software/Firmware
- Topic: Simplify3D Software
- Replies: 74
- Views: 17741
Re: Simplify3D Software
What settings do you use Seaton?
What profile? Replicator 2 as default and than use the Felix dimensions and steps?
What profile? Replicator 2 as default and than use the Felix dimensions and steps?