Search found 45 matches

by aikx
Mon Apr 24, 2017 8:00 pm
Forum: Deutsch
Topic: Suche Deutsche ;)
Replies: 33
Views: 6483

Re: Suche Deutsche ;)

Vielleicht, weil die Meisten auf Englisch schreiben?
Leider ist ein großer Teil der User auf der Strecke geblieben, als die Forumssoftware sehr nachlässig umgestellt wurde. Die Firma meldet sich nur sporadisch mit ihrem zweifellos vorhandenen Fachwissen.
by aikx
Tue Aug 16, 2016 2:38 pm
Forum: Electronics
Topic: Shifting and hot electronics
Replies: 7
Views: 1638

Re: Shifting and hot electronics

I am not sure about that. The part was printed correct ~3h out of 4h. I did a little bit of research and probably it's an different problem. After 3h the stepper motor driver ICs overheated and stopped working, maybe some seconds the running move-signals are ignored. After that the print is shifted...
by aikx
Mon Aug 15, 2016 10:06 am
Forum: Electronics
Topic: Shifting and hot electronics
Replies: 7
Views: 1638

Re: Shifting and hot electronics

...There are potentiometers on the board, but i cant find a documentation about them.n There is documentation in the manual /assembly instructions. 1. Turn the screw fully counter-clockwise. 2. Turn it clockwise a quarter turn. This will give a good starting point for finetuning later. from Instruc...
by aikx
Mon Aug 15, 2016 9:45 am
Forum: Electronics
Topic: Working F 3.1 , but Display doesn't
Replies: 7
Views: 1348

Re: Working F 3.1 , but Display doesn't

See also: http://www.felixprinters.com/forum/viewtopic.php?f=14&t=998&p=6106&hilit=potentiometer#p6106 Lighting is on, but no characters are displayed: Contrast of the display is not set-up correctly. Turn the potentiometer on the FELIXprinters electronics board according to the assembly manual. fro...
by aikx
Mon Aug 15, 2016 9:34 am
Forum: Electronics
Topic: Working F 3.1 , but Display doesn't
Replies: 7
Views: 1348

Re: Working F 3.1 , but Display doesn't

toonlumberjack wrote:Well, My printer does work with laptop via USB. Besides Shifting and other calibration problems the display doesn't work like intended.
Does it show any values?
Does it show anything ever?
Did you activate the display support in Firmware, Marlin/Repetier?
by aikx
Mon Apr 11, 2016 9:28 am
Forum: Hacks and printer upgrades
Topic: Changing from Dual to Single extruder
Replies: 3
Views: 1911

Re: Changing from Dual to Single extruder

Bobbystone wrote:... my felix dual ...
What Version?: 1,2,3,Pro?
by aikx
Sat Feb 27, 2016 12:11 am
Forum: General
Topic: Motor buzzes
Replies: 6
Views: 3719

Re: Motor buzzes

evanr wrote:...Anyways, it prints ok but the prints are now shifting when printing..... it never ends
Go back to my post....
by aikx
Sun Feb 21, 2016 11:08 am
Forum: General
Topic: Motor buzzes
Replies: 6
Views: 3719

Re: Motor buzzes

I've done the following: - swapped the leads in the Arduino from x,y,z to the extruder motor and it is good. - changed extruder motor to the spare motor controller on Arduino (I don't have a 2nd extruder), still a problem Did you: "Important note: The potmeter (little screw) on the stepper drivers ...
by aikx
Wed Jan 06, 2016 10:22 am
Forum: Electronics
Topic: Crazy display after not using it for a few weeks
Replies: 1
Views: 8339

Re: Crazy display after not using it for a few weeks

Try Arduino IDE 1.6.5
by aikx
Mon Jan 04, 2016 9:54 am
Forum: General
Topic: Felix 2.0 sample _40x10 print problem
Replies: 3
Views: 17263

Re: Felix 2.0 sample _40x10 print problem

Slice with SFact
2_1_Normal_quality_no_support
PLA 1.75mm color RED
Print Temp 170-240C
Feedrate 100
First reduce the distance between Hotend and bed, use a sheet of paper.
Second try a Feedrate of 50%, to see if the extruder has a problem?

Go to advanced search