Troubleshooting

New Topic
  • Topics
    Replies
    Views
    Last post
  • Erratic Hot-end Temperatures
    by Caelum »
    6 Replies
    2211 Views
    Last post by andrewsi
  • X-axis error
    by z0rak »
    5 Replies
    1024 Views
    Last post by vyndalin
  • Blobs where new layers begin
    by stiffmasters »
    3 Replies
    848 Views
    Last post by andrewsi
  • Extruder Temperature jumping fast up/down
    by frankjoke »
    4 Replies
    1670 Views
    Last post by frankjoke
  • extruder motor has quit!!
    by robots inc. »
    2 Replies
    530 Views
    Last post by satoer
  • Extrusion stops at about 100 layers
    by JGT »
    1 Replies
    949 Views
    Last post by Dreide
  • Filament feed rate problem
    by 1828peter »
    1 Replies
    667 Views
    Last post by Saamec
  • Problem with Hot End v4 Thermistor.
    by Metalrat »
    4 Replies
    1004 Views
    Last post by felix GH
  • SD Card detection reversed
    by fishbyte »
    1 Replies
    496 Views
    Last post by andrewsi
  • Trouble prining solid infil
    by Capella_Ben »
    18 Replies
    2399 Views
    Last post by mcorb
  • Alternative connection for main fan
    by Lonos »
    1 Replies
    545 Views
    Last post by Bachgassenbande
  • Head lost Ventilator screw within print
    by frankjoke »
    0 Replies
    549 Views
    Last post by frankjoke
  • Periodic Extruder Quality Issue
    by sam »
    4 Replies
    889 Views
    Last post by Dreide
  • Unstable hot end temperature?
    by Dreide »
    12 Replies
    2574 Views
    Last post by Dreide
  • Printbed is fairly level, but slightly inclined :-/
    by andrewsi »
    4 Replies
    790 Views
    Last post by andrewsi
  • X and Y axis wobble ?
    by alanh »
    3 Replies
    1274 Views
    Last post by alanh
  • Initial axis calibration
    by nosomis »
    1 Replies
    1504 Views
    Last post by andrewsi
  • Problem first layer and wall printing
    by Bitpower »
    1 Replies
    740 Views
    Last post by Capella_Ben
  • Z home or - direction triggering failure.
    by kdixon »
    8 Replies
    1200 Views
    Last post by andrewsi
  • Extruder motor playing up
    by Ramon »
    7 Replies
    1434 Views
    Last post by Ramon
  • Sagging printhead assembly
    by Hugues »
    28 Replies
    7373 Views
    Last post by Capella_Ben
  • What type of silicone?
    by Capella_Ben »
    2 Replies
    578 Views
    Last post by Capella_Ben
  • All Output Suddenly Stops (when idle)
    by reltnek »
    2 Replies
    643 Views
    Last post by reltnek
  • Extruder Stepper motor fail
    by markus_kyroe »
    3 Replies
    862 Views
    Last post by markus_kyroe
  • First layer weirdness
    by instasquid »
    2 Replies
    758 Views
    Last post by lammert
New Topic

Return to Board Index

Forum permissions

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum