Troubleshooting

New Topic
  • Topics
    Replies
    Views
    Last post
  • How to change X axis home location.
    by weri32 »
    2 Replies
    983 Views
    Last post by weri32
  • thermistor case
    by stillcool40 »
    1 Replies
    465 Views
    Last post by satoer
  • hot end, I give up!
    by stillcool40 »
    2 Replies
    641 Views
    Last post by satoer
  • all temp readings show 'def' and printer goes offline
    by frankjoke »
    3 Replies
    692 Views
    Last post by JohnK1
  • Heater Cartridge Failure, Z-Axis Motor Failure...
    by Tomas »
    0 Replies
    705 Views
    Last post by Tomas
  • Strange extruder temp deviations
    by frankjoke »
    2 Replies
    517 Views
    Last post by frankjoke
  • Filament trouble feeding extruder head
    by ibkanat »
    2 Replies
    949 Views
    Last post by fanna
  • Not consistent Z height
    by temo »
    2 Replies
    650 Views
    Last post by temo
  • Extruder skipping
    by kerog »
    0 Replies
    589 Views
    Last post by kerog
  • Problems keeping hot-ends level
    by kerog »
    4 Replies
    860 Views
    Last post by kerog
  • Hot-end fan is not working
    by robots inc. »
    3 Replies
    760 Views
    Last post by Legion 2.3
  • Nozzle clear and clean?
    by starburstquicks »
    4 Replies
    931 Views
    Last post by starburstquicks
  • PLA goes not through the nozzle
    by pixeltroll »
    4 Replies
    983 Views
    Last post by pixeltroll
  • XZ Home Triggering Failure
    by reltnek »
    4 Replies
    943 Views
    Last post by Legion 2.3
  • Problem with first layer
    by michalp »
    8 Replies
    1344 Views
    Last post by 3djohny
  • Levelling the Building Plate
    by kiteboarder »
    3 Replies
    666 Views
    Last post by agentmulder
  • Leveling out the printbed
    by temo »
    11 Replies
    2612 Views
    Last post by agentmulder
  • Z axis steps to big
    by Deluka »
    2 Replies
    804 Views
    Last post by Deluka
  • One side melting/sagging
    by Inkrig »
    1 Replies
    545 Views
    Last post by Dreide
  • I think no heating... def / 0C on display
    by michalp »
    6 Replies
    734 Views
    Last post by michalp
  • Printer misreads position mid-print
    by polymerled »
    2 Replies
    449 Views
    Last post by polymerled
  • Filament jam
    by instasquid »
    23 Replies
    5736 Views
    Last post by polymerled
  • First Print-Filament won't feed
    by Formatize »
    6 Replies
    1060 Views
    Last post by Formatize
  • All heaters (two extruders & print bed) no longer working?!
    by SunBoley »
    5 Replies
    709 Views
    Last post by SunBoley
  • Warped bed, getting worse
    by Legion 2.3 »
    4 Replies
    900 Views
    Last post by killejano
New Topic

Forum permissions

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum