Software/Firmware

Discussions about firmware/slicing software, tweaks and settings
  • Forum
    Topics
    Posts
    Last post
New Topic
  • Topics
    Replies
    Views
    Last post
  • Mac users - please raise your hand...
    by Kjetilei »
    64 Replies
    18549 Views
    Last post by jefstaes
  • Guide for using your FelixPrinter on a Linux Host
    by wmeertens »
    8 Replies
    5446 Views
    Last post by CSP
  • Ooze Control Dual Head + Simplify
    by seaton »
    2 Replies
    1870 Views
    Last post by DDME-MarcUser avatar
  • Anybody tested MatterControl?
    by frankjoke »
    2 Replies
    1540 Views
    Last post by Beta
  • Using a FELIX 3.0 with LabVIEW
    by bob75 »
    3 Replies
    1536 Views
    Last post by Dreide
  • Touchscreen Display Problem of Felix Pro 2 Touch
    by afza93 »
    8 Replies
    1647 Views
    Last post by afza93
  • Cura Profile/config available for Felix Pro2?
    by tuxophil »
    2 Replies
    2426 Views
    Last post by tuxophil
  • Profiles for new Cura 2.3 for Felix 3.1?
    by kerog »
    0 Replies
    1956 Views
    Last post by kerog
  • Firmware Errors
    by Wombat32 »
    1 Replies
    1449 Views
    Last post by gfeliksdalUser avatar
  • feed speed reduction for "skin layer" in flat parts
    by Niho3D »
    2 Replies
    14510 Views
    Last post by Dreide
  • Felix Dual to Single, Firmware problems
    by Bobbystone »
    2 Replies
    1355 Views
    Last post by Dreide
  • Software install
    by evanr »
    1 Replies
    2244 Views
    Last post by Sander_Felix
  • Felix Pro1 Simplify 3D
    by sbau »
    0 Replies
    1432 Views
    Last post by sbau
  • Dual Head - Trouble
    by Dominic »
    2 Replies
    1729 Views
    Last post by Dominic
  • SIMPLIFY3D Settings
    by jezurender »
    1 Replies
    1805 Views
    Last post by venkel
  • Repetier-Host 1.6.1 preheat problem
    by icecube_it »
    2 Replies
    1455 Views
    Last post by icecube_it
  • Where I can get torrent XRumer + SocPlugin??
    by Staceyzzjef »
    0 Replies
    1498 Views
    Last post by Staceyzzjef
  • Cura Engine Perimeter-Loop-Infill order
    by stiffmasters »
    0 Replies
    1497 Views
    Last post by stiffmasters
  • problems update firmware
    by gido »
    3 Replies
    3273 Views
    Last post by janwijbrandUser avatar
  • No Preview - Repetier Hangs
    by evanr »
    0 Replies
    6131 Views
    Last post by evanr
  • Repetier 1.5.6 update ???
    by alanh »
    3 Replies
    1729 Views
    Last post by agentmulder
  • Printer wont connect to Repetier - reinstall driver? - how?
    by agentmulder »
    0 Replies
    2047 Views
    Last post by agentmulder
  • Felix settings for Repetier Host 1.6 where?
    by agentmulder »
    0 Replies
    1492 Views
    Last post by agentmulder
  • IndieGoGo - Support development of an open source slicer and
    by Stanek3Dim »
    1 Replies
    1280 Views
    Last post by Stanek3Dim
  • Gcode pause and start through lCD control?
    by wilco02 »
    0 Replies
    1347 Views
    Last post by wilco02
New Topic

Return to Board Index

Forum permissions

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum