Software/Firmware

Discussions about firmware/slicing software, tweaks and settings
  • Forum
    Topics
    Posts
    Last post
New Topic
  • Topics
    Replies
    Views
    Last post
  • is the v0.92 firmware relevant to Felix2 models?
    by agentmulder »
    2 Replies
    723 Views
    Last post by satoer
  • Repetier Host 1.0.6 please !!!
    by alanh »
    0 Replies
    930 Views
    Last post by alanh
  • E-step calibration
    by kerog »
    1 Replies
    547 Views
    Last post by DDME-MarcUser avatar
  • replacing extruder with e3d extruder
    by woutzweers »
    3 Replies
    729 Views
    Last post by seaton
  • using Cura instead of repetierhost
    by Theo Schumacher »
    5 Replies
    2982 Views
    Last post by fesch
  • Repetier host freezes up comp
    by Niho3D »
    0 Replies
    655 Views
    Last post by Niho3D
  • Dual Extrusion Support - Nozzle hits the print
    by hanscl »
    4 Replies
    2274 Views
    Last post by neep
  • New fork of Marlin firmware for Felix on Github
    by andrewsi »
    8 Replies
    2885 Views
    Last post by Chris.E
  • FELIX 3: Wrong time calculation
    by Rafjax »
    0 Replies
    639 Views
    Last post by Rafjax
  • Linux Software?
    by gskillas »
    5 Replies
    1312 Views
    Last post by FrankGarza
  • Update 1.05 and firmware 0,92 (?) issue
    by elshout »
    12 Replies
    2101 Views
    Last post by Chris.E
  • Reconfig / Calibrate Steps per MM?
    by stratogavster »
    8 Replies
    2578 Views
    Last post by kanita
  • newbie help slicing
    by Niho3D »
    2 Replies
    415 Views
    Last post by Niho3D
  • Cura for Mac?
    by kerog »
    3 Replies
    839 Views
    Last post by markchagers
  • Latest Software/firmware for Felix 1.0
    by gfeliksdal »
    46 Replies
    19934 Views
    Last post by frankjoke
  • Repetier Host Freezes/ gets stuck
    by retsac »
    0 Replies
    806 Views
    Last post by retsac
  • updating firmware
    by stillcool40 »
    21 Replies
    2545 Views
    Last post by DDME-MarcUser avatar
  • September 2014 Firmware Update
    by kerog »
    3 Replies
    1035 Views
    Last post by scp
  • september firmware update
    by pixeltroll »
    0 Replies
    741 Views
    Last post by pixeltroll
  • KISSlicer dual extrusion settings
    by kerog »
    7 Replies
    2644 Views
    Last post by DDME-MarcUser avatar
  • where can i find the printer setting values for Repetier?
    by fletchfletch1971 »
    0 Replies
    805 Views
    Last post by fletchfletch1971
  • temperatuur tweede laag repetier
    by Aaron »
    0 Replies
    656 Views
    Last post by Aaron
  • Different Speed for Each Extruder ?
    by livingstereo1991 »
    1 Replies
    422 Views
    Last post by frankjoke
  • KISSlicer rotation bug?
    by scp »
    2 Replies
    653 Views
    Last post by scp
  • mess after some right layers
    by pixeltroll »
    1 Replies
    566 Views
    Last post by pla_GodX
New Topic

Forum permissions

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum