General

This is for general discussions. Also FAQ can be found here.

Moderator: speedake95

  • Forum
    Topics
    Posts
    Last post
New Topic
  • Topics
    Replies
    Views
    Last post
  • *(SOLVED)Print shift about 1-2 cm in Y directions ?!?
    by naser404 »
    6 Replies
    927 Views
    Last post by naser404
  • SUPERURGENT! Hot End Jams
    by twicx »
    3 Replies
    638 Views
    Last post by twicx
  • ABS for Felix
    by angryangel »
    0 Replies
    524 Views
    Last post by angryangel
  • Coloring 3DPrints
    by rad »
    1 Replies
    427 Views
    Last post by satoer
  • Sloped printing when printing dual parts
    by tomasf »
    2 Replies
    473 Views
    Last post by rad
  • reset temperature
    by Luca »
    5 Replies
    729 Views
    Last post by Luca
  • Twisted Jar Part
    by RobGer »
    13 Replies
    1659 Views
    Last post by RobGer
  • Im done figthing the extruder
    by Lioric »
    25 Replies
    4377 Views
    Last post by Lioric
  • Can't heat extruder and printbed
    by markus_kyroe »
    3 Replies
    506 Views
    Last post by markus_kyroe
  • Extruder trouble
    by killejano »
    11 Replies
    1720 Views
    Last post by satoer
  • Print stops suddenly
    by kimmoli »
    1 Replies
    428 Views
    Last post by kimmoli
  • Where to find a complete file-set ?
    by tomasf »
    0 Replies
    619 Views
    Last post by tomasf
  • Removing parts with cold-spray
    by kimmoli »
    2 Replies
    454 Views
    Last post by kimmoli
  • Problem: Limit switch is active everytime
    by benjamin »
    2 Replies
    595 Views
    Last post by dognotdog
  • 1st page in manual & parts don't match !!
    by naser404 »
    12 Replies
    2099 Views
    Last post by framirez
  • Problems with heating bed - MAX 60 degrees
    by markus_kyroe »
    7 Replies
    1769 Views
    Last post by markus_kyroe
  • speeds
    by AnttiS »
    3 Replies
    624 Views
    Last post by satoer
  • Jittery prints on flat pieces?
    by twicx »
    8 Replies
    1984 Views
    Last post by felix
  • material in bed
    by AnttiS »
    1 Replies
    390 Views
    Last post by Kjetilei
  • 3D printer meetup
    by Kjetilei »
    2 Replies
    699 Views
    Last post by Kjetilei
  • Very Sensitive Electronics
    by daveinhull »
    5 Replies
    803 Views
    Last post by daveinhull
  • Some advice on print problems
    by daveinhull »
    2 Replies
    600 Views
    Last post by daveinhull
  • Please can I have the profile that created this???
    by daveinhull »
    5 Replies
    880 Views
    Last post by daveinhull
  • Starting to get there with SFACT slicer
    by daveinhull »
    3 Replies
    836 Views
    Last post by Kjetilei
  • My new printer, upgrade ideas, and fillaments
    by twicx »
    2 Replies
    557 Views
    Last post by twicx
New Topic

Forum permissions

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum