Assembly

Help eachother out with assembly problems.
New Topic
  • Topics
    Replies
    Views
    Last post
  • Assembly Manual Felix 3.1 - Step 43
    by dobst »
    3 Replies
    2254 Views
    Last post by gfeliksdalUser avatar
  • Z Axis motor connector dead?
    by emu »
    1 Replies
    1821 Views
    Last post by emu
  • Felix 2.0 hotend on Felix 1.0 ?
    by danielkschneider »
    0 Replies
    1827 Views
    Last post by danielkschneider
  • Y axis opto stop on 3.1 dual
    by Brico »
    0 Replies
    1058 Views
    Last post by Brico
  • 3.1 upgrade, Fan Assembly
    by DocMooney »
    4 Replies
    1433 Views
    Last post by DocMooney
  • Upgrade 3.0 to 3.1 Z-axes calibration part not explained
    by Metalrat »
    4 Replies
    1403 Views
    Last post by gfeliksdalUser avatar
  • 3.1 Upgrade X axis belt mount
    by kerog »
    4 Replies
    1396 Views
    Last post by kerog
  • Felix 3.0 Step 21 Z-Axis Lift Part doesn't fit (solved)
    by michael.ecker »
    6 Replies
    2030 Views
    Last post by berfel
  • Upgrade instructions 3.0 --> 3.1
    by fesch »
    0 Replies
    1155 Views
    Last post by fesch
  • complaint: quality of the manual and parts
    by neep »
    8 Replies
    2051 Views
    Last post by agentmulder
  • Felix 3.0 Steps 42, 46, 70 and 105 missing parts
    by michael.ecker »
    4 Replies
    1510 Views
    Last post by agentmulder
  • Stepper motor rotation wrong
    by fesch »
    1 Replies
    1101 Views
    Last post by fesch
  • Extruder motors not responding
    by seaton »
    0 Replies
    1205 Views
    Last post by seaton
  • motor bracket?
    by neep »
    2 Replies
    1134 Views
    Last post by neep
  • putting bearing balls back into bearing set
    by neep »
    0 Replies
    1108 Views
    Last post by neep
  • LooseHot End Screw... A Good thing?
    by WayneC »
    1 Replies
    1042 Views
    Last post by Dreide
  • Can I buy Kapton sheets for the v3 heatbed in europe?
    by Eriond »
    6 Replies
    2286 Views
    Last post by Eli-Audio
  • Fixing v3 Z opto sensor in place
    by drfoop »
    9 Replies
    2929 Views
    Last post by Eli-Audio
  • V1.5 to V3
    by daveinhull »
    9 Replies
    1826 Views
    Last post by daveinhull
  • Which Extruder is it?
    by jjlink »
    2 Replies
    1160 Views
    Last post by jjlink
  • Wobble between Z-axis lift bearings
    by todd »
    3 Replies
    1385 Views
    Last post by todd
  • User Workshop
    by jefstaes »
    3 Replies
    1631 Views
    Last post by Makron
  • Step 22. Z carrier distortion
    by RAD Design »
    1 Replies
    1185 Views
    Last post by kerog
  • Annotated Assembly Manual PDF
    by kerog »
    3 Replies
    1819 Views
    Last post by ottoveen
  • New case for electronics after upgrade to new power suplly
    by ebiz@centrum.cz »
    0 Replies
    1299 Views
    Last post by ebiz@centrum.cz
New Topic

Return to Board Index

Forum permissions

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum