Page 1 of 1

Generated g-code not found

Posted: Thu Jun 05, 2014 9:06 am
by Rinse
Hi ,

I installed the repetier-host for felix printers V0.90C

Slicing with Slic3r is 1 of the options .

However when I start slic3r it almost directly generates the error message " Generated g-code not found "

please see attachment,

can anyone help?

Re: Generated g-code not found

Posted: Fri Jun 06, 2014 4:14 pm
by Legion 2.3
this problem can occur if the slicer has a problem slicing your object
OR you have invalid slicing settings, for example a layer height of 0,2 instead of 0.2. Look at the log output, if there is an error, it will be displayed there.

Try using these settings:

Code: Select all

# generated by Slic3r 1.0.1 on Fri Jun  6 17:08:21 2014
avoid_crossing_perimeters = 
bed_size = 255,205
bed_temperature = 55
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 50
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 300
disable_fan_first_layers = 30
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors
external_perimeter_speed = 100%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0,0x0
extrusion_axis = E
extrusion_multiplier = 1,1
extrusion_width = 0
fan_always_on = 
fan_below_layer_time = 60
filament_diameter = 1.75,3
fill_angle = 45
fill_density = 0.25
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_bed_temperature = 55
first_layer_extrusion_width = 200%
first_layer_height = 0.2
first_layer_speed = 60%
first_layer_temperature = 200,200
g0 = 0
gap_fill_speed = 40
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 100
layer_gcode = 
layer_height = 0.2
max_fan_speed = 100
min_fan_speed = 30
min_print_speed = 10
min_skirt_length = 0
notes = 
nozzle_diameter = 0.35,0.35
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process = 
print_center = 127.5,102.5
raft_layers = 0
randomize_start = 
resolution = 0
retract_before_travel = 2,2
retract_layer_change = 1,1
retract_length = 1,1
retract_length_toolchange = 10,10
retract_lift = 0.2,0.2
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 30,30
rotate = 0
scale = 1
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 30
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_below_area = 30
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 70
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 0
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_pattern = honeycomb
support_material_spacing = 10
support_material_speed = 120
support_material_threshold = 0
temperature = 190,200
thin_walls = 1
threads = 4
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 60
top_solid_layers = 3
travel_speed = 130
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 10
wipe = 0,0
z_offset = 0
You can import these settings by using the standard windows editor, save it as .ini and you can use it with slic3r.