High quality prints

This is for general discussions. Also FAQ can be found here.

Moderator: speedake95

Post Reply
satoer
Posts: 436
Joined: Mon Oct 01, 2012 8:00 pm
Location: Netherlands

Re: High quality prints

Post by satoer »

though obvious overhang troubles
Just call it nose and beard hair!
My Felix 1.5 printed designs on Thingiverse
E3D V6 Hot end upgrade for your Felix
Tweezer bracket for your Felix
Led bar upgrade for your Felix

kerstens
Posts: 10
Joined: Tue Oct 16, 2012 4:23 pm

Post by kerstens »

Hello Stratogavster,

Is it possible to share your profile with use? I like your print quality.

stratogavster
Posts: 120
Joined: Tue Jul 17, 2012 9:04 pm
Location: United Kingdom

Post by stratogavster »

I'll certainly share the profile!!....though still tweaking it trying to find that magic balance across differing geometry and require quality. Also in the process of upgrading to v1.5 so not sure how valid the profiles will remain once i've made the upgrade, but i'll be sure to share asap!

maoz
Posts: 22
Joined: Mon Apr 15, 2013 9:54 am
Location: Saint-Petersburg, Russia

Post by maoz »

Hi.
Got any resulst for last year or it's abandoned fork?

Bachgassenbande
Posts: 132
Joined: Sat Jul 20, 2013 12:50 pm
Location: Würzburg

Post by Bachgassenbande »

That my first try to generate a high quality part.
To my shame the extruder was not calibrated 100% correct.
IMG_20130910_170902_466.jpg
Seems like I hae to tweak the settings in KISSLICER a litte bit more to prevent the hole.
IMG_20130910_171028_490.jpg
Felix 2.0
E3D Kraken Hotend
3mm Glas bed
LED light bar upgrade

Bachgassenbande
Posts: 132
Joined: Sat Jul 20, 2013 12:50 pm
Location: Würzburg

Post by Bachgassenbande »

Just played a little bit with KISSlicer and want to share my results:
IMG_20130922_142549_141.jpg
IMG_20130922_142645_429.jpg
IMG_20130922_142734_118.jpg
IMG_20130922_142906_481.jpg
Parameters for printing:
Settings.PNG
Felix 2.0
E3D Kraken Hotend
3mm Glas bed
LED light bar upgrade

twicx
Posts: 105
Joined: Fri Jan 11, 2013 1:26 pm

Post by twicx »

Just wondering if someone can give be a bit of direction.

I'm trying to print with smaller layer heights to get a higher quality print. I know something has to be done with the retraction settings, but I don't know what. I've become increasingly pleased with using Slic3r, so if someone could advise me on what retraction and layer height should, that would be a big help. Currently, layer height is at 0.2 and I don't know where retraction settings are in slic3r.

any help?

satoer
Posts: 436
Joined: Mon Oct 01, 2012 8:00 pm
Location: Netherlands

Post by satoer »

Not sure what the relation is with retraction settings and layer height but:
I'ts on the tab "Printer Settings"
Than "Extruder 1" from the left selection box.
There are the retraction settings. Adjust, save the printer profile and don't forget to select this profile in repetier host.
My Felix 1.5 printed designs on Thingiverse
E3D V6 Hot end upgrade for your Felix
Tweezer bracket for your Felix
Led bar upgrade for your Felix

twicx
Posts: 105
Joined: Fri Jan 11, 2013 1:26 pm

Post by twicx »

aha! I see now. So what would you suggest for layer height and retraction?

Mayhem
Posts: 169
Joined: Tue Jan 08, 2013 4:15 pm
Location: Finland

Post by Mayhem »

Made landin gear and vibration plate for my hexa copter :)
Whit ninja flex and pla
Attachments
IMG_0394.JPG
IMG_0395.JPG
Felix 2.0----> 3.0
V4 hot end
Simplyfy 3D
Kisslicer
Autodesk fusion 360

Post Reply

Return to “General”