recived my Felix 2.0

This is for general discussions. Also FAQ can be found here.

Moderator: speedake95

Post Reply
angryangel
Posts: 110
Joined: Sun Mar 31, 2013 11:01 am
Location: Germany near Heilbronn / Heidelberg
Contact:

recived my Felix 2.0

Post by angryangel »

Hello

Yesterday i recived my Felix 2.0

That looks like this:
That looks like this
That looks like this
Some hours later:
Some houers later
Some houers later
Today

first testprint after sucsefull leveling the bed
testprint
testprint

First realprint in Draft quality:
mouse 1
mouse 1
mouse 2
mouse 2

aikx
Posts: 45
Joined: Sun May 13, 2012 1:14 pm
Location: Cologne, Germany

Post by aikx »

My Gratulation!

Kjetilei
Posts: 334
Joined: Fri Mar 16, 2012 8:26 pm
Location: Stavanger, Norway

Post by Kjetilei »

Congratulations!

Thanks for sharing.

Did you have any problems with the build or was it a nice experience?

angryangel
Posts: 110
Joined: Sun Mar 31, 2013 11:01 am
Location: Germany near Heilbronn / Heidelberg
Contact:

Post by angryangel »

Thanks

the build was easy for me everything worked fin

just te leveling of the bed is a littel bit difficult and it is still not perfect

and the first layer don´t stick on some small places bevor this place and after it , it stics perfect
this only heppens when it extrud over a long distance linear

perhaps there the kapton is dirty?

or any idears??

Makron
Posts: 110
Joined: Wed Mar 20, 2013 1:29 pm

Post by Makron »

Congratulations it looks good !!!

Yes its the tape clean it with aceton , i do it before printing every time.

Can you make some pics of the z axis ??

satoer
Posts: 436
Joined: Mon Oct 01, 2012 8:00 pm
Location: Netherlands

Post by satoer »

Nice! These are the first pictures of the 2.0 Ive seen! The hotbed looks the same as the 1.0 / 1.5? If you push a screwdriver on the frame touching the z-rod, do you see it wobbling if it turns?
My Felix 1.5 printed designs on Thingiverse
E3D V6 Hot end upgrade for your Felix
Tweezer bracket for your Felix
Led bar upgrade for your Felix

angryangel
Posts: 110
Joined: Sun Mar 31, 2013 11:01 am
Location: Germany near Heilbronn / Heidelberg
Contact:

Post by angryangel »

@ makron i can make pictures later of the axis but if you download the manuel from the downloadesction you sie it much better

@ satoer where sschould i push the screwdriver? i cannot imagine what you mean have you a picture of that??

i dont know the hotbed of the felix 1.0 or 1.5 but the foilheater was complet assembeld i juste have to put it on the aluminium table

Kjetilei
Posts: 334
Joined: Fri Mar 16, 2012 8:26 pm
Location: Stavanger, Norway

Post by Kjetilei »

@satoer: the hotbed has been updated with a thin Kapton based heater. Go to downloads and download the 2.0 manual to see the changes.

angryangel
Posts: 110
Joined: Sun Mar 31, 2013 11:01 am
Location: Germany near Heilbronn / Heidelberg
Contact:

Post by angryangel »

the bed is at 55°c in 3 minutes or less and the thermistor shows the real temperture of the bed i tested it with a infrared thermometer

alexandrestcyr
Posts: 4
Joined: Sat May 11, 2013 3:19 pm

Post by alexandrestcyr »

really nice!! Cant wait to get my felix 2.0 !! the quality is impressive

Post Reply