Hi
this bed-leveling-help i found on thingivers but it dosent work with the original file because the felix have an other bed size
so i made i simmiler one that fits better to the bed of ouer felix printer
today i tested it
i just printed and mesured the layer hig at different positions and after that i adjusted it and print again until the layer high was the same at evey position for me it worked very good
perhaps it helps someone too
her is the link to the original
i do not really understand the instruktions for my file i juste used the normal settings and mesuered as discribed above
http://www.thingiverse.com/thing:15709
my fil is just one layer high and wide
Last visit was:
It is currently Sat Jan 23, 2021 3:02 pm
Bed Leveling help-file
This is for general discussions. Also FAQ can be found here.
Moderator: speedake95
-
- Posts: 110
- Joined: Sun Mar 31, 2013 11:01 am
- Location: Germany near Heilbronn / Heidelberg
- Contact:
Bed Leveling help-file
Post by angryangel »
- Attachments
-
- bed-level2.stl
- (39.39 KiB) Downloaded 37 times
Jump to
- General
- ↳ Official FELIXprinters News
- ↳ FELIXprinters.com feedback
- Hardware
- ↳ FELIX Pro Series
- ↳ General Discussion
- ↳ Assembly and first print
- ↳ Electronics
- ↳ Mechanics
- ↳ Troubleshooting
- ↳ Hacks and upgrades
- ↳ FELIX Tec Series
- ↳ General Discussion
- ↳ Assembly and first print
- ↳ Electronics
- ↳ Mechanics
- ↳ Troubleshooting
- ↳ Hack and upgrades
- ↳ FELIX Pro L Series
- ↳ General Discussion
- ↳ Assembly and first print
- ↳ Electronics
- ↳ Mechanics
- ↳ Troubleshooting
- ↳ Hack and upgrades
- ↳ Additional Hardware
- ↳ Extruders & Hotends
- ↳ Older FELIXprinters upgrades
- ↳ Archive
- ↳ Hacks and printer upgrades
- ↳ Troubleshooting
- ↳ Assembly
- ↳ Mechanics
- ↳ Electronics
- ↳ General
- Software/Firmware
- ↳ FELIXbuilder
- ↳ Simplify3D
- ↳ Repetier-Host
- ↳ Kisslicer
- ↳ CURA
- ↳ Firmware
- ↳ General
- ↳ PrusaSlicer
- The Art of 3d printing
- ↳ Tips and Tricks
- ↳ What have you made? Show off your projects
- Materials
- ↳ FELIXprinters filaments
- ↳ Other filaments
- ↳ Troubleshooting
- ↳ General
- Languages
- ↳ Nederlands
- ↳ Deutsch
- ↳ Español
- ↳ Italiano
- ↳ português
- BIO-printing
- ↳ BIO-INK
- ↳ Alginate
- ↳ Gellan gum
- ↳ Agarose
- ↳ Gelatine
- ↳ Collagen
- ↳ Pluronics
- ↳ PEG
- ↳ Applications
- ↳ Validated
- ↳ Non-Validated
- ↳ Print file library
- ↳ Q&A
- ↳ Publications
- ↳ Comments, requests, and suggestions
- Back to Main Website Board index
- All times are UTC+01:00
- Delete cookies
- Privacy
- Terms
- Contact us