Hi dognotdog, I tried again with different browsers and the same result, the file opens fine but when I tried to unzip it with WinRAR, 7zip - says all the files are corrupted except for the carriage.stl (only after zip repair).
For ABS, I'm concerned that the shrinkage might affect the mounting of the various hardware, so I will probably go with PLA.
[WIP] another direct dual extruder
Hi dognotdog, I tried two different computers, same results.
You can see the files in the winzip / WinRar / 7zip windows, but when you try to extract them, it just keeps saying the files are corrupted.
Maybe use another compressor ? 7zip or WinRar ?
Thanks, I need your help to upgrade to a dual extruder using your design.
You can see the files in the winzip / WinRar / 7zip windows, but when you try to extract them, it just keeps saying the files are corrupted.
Maybe use another compressor ? 7zip or WinRar ?
Thanks, I need your help to upgrade to a dual extruder using your design.
Hi dognotdog, I tried and tried, cannot open your zip file with anything that does not say that it is corrupted. I seriously think that maybe it's not meant to be extracted at all. What did you used to zip it with?
Did anyone here successfully extracted the files from this zip and not just opened it to view contents? Maybe on a Mac?
*frustrated*
Did anyone here successfully extracted the files from this zip and not just opened it to view contents? Maybe on a Mac?
*frustrated*
I get this:
! C:\Users\UserName\Downloads\dual-extruder.zip: Unexpected end of archive
! C:\Users\UserName\Downloads\dual-extruder.zip: Unexpected end of archive
Felix 3.0 with E3D Dual direct drive extruder conversion. (http://forum.felixprinters.com/viewtopic.php?f=9&t=1630)
Software: simplify3d
Software: simplify3d
Tried here....
7-Zip [64] 9.20 Copyright (c) 1999-2010 Igor Pavlov 2010-11-18
p7zip Version 9.20 (locale=en_GB.UTF-8,Utf16=on,HugeFiles=on,8 CPUs)
Processing archive: dual-extruder.zip
ERROR: E_FAIL
Then with zip -FF to fix it and came up with this...
Fix archive (-FF) - salvage what can
Found end record (EOCDR) - says expect single disk archive
Scanning for entries...
copying: carriage.STL (45308 bytes)
copying: faceplate.STL (359234 bytes)
copying: tension-arm.STL (16552 bytes)
Central Directory found...
no local entry: fan-mount.STL
EOCDR found ( 1 630926)...
inflating: carriage.STL
inflating: faceplate.STL bad CRC a3163b87 (should be 8841ce1f)
inflating: tension-arm.STL bad CRC a63c203c (should be 46d01091)
7-Zip [64] 9.20 Copyright (c) 1999-2010 Igor Pavlov 2010-11-18
p7zip Version 9.20 (locale=en_GB.UTF-8,Utf16=on,HugeFiles=on,8 CPUs)
Processing archive: dual-extruder.zip
ERROR: E_FAIL
Then with zip -FF to fix it and came up with this...
Fix archive (-FF) - salvage what can
Found end record (EOCDR) - says expect single disk archive
Scanning for entries...
copying: carriage.STL (45308 bytes)
copying: faceplate.STL (359234 bytes)
copying: tension-arm.STL (16552 bytes)
Central Directory found...
no local entry: fan-mount.STL
EOCDR found ( 1 630926)...
inflating: carriage.STL
inflating: faceplate.STL bad CRC a3163b87 (should be 8841ce1f)
inflating: tension-arm.STL bad CRC a63c203c (should be 46d01091)